Reference

Pitch Bend, Aftertouch, NRPN & SysEx — when you need them

For most rigs, three message types do almost everything: Control Change toggles and sweeps parameters, Program Change recalls presets and scenes, and Note triggers or holds things. That covers roughly 95% of what you'll ask a plugin or amp sim to do — so start there. This page is about the other 5%: the less-common messages MIDIRover can send through its Advanced MIDIaction when a specific parameter or piece of gear asks for them.

Start with CC, Program Change and Note

Before reaching for anything here, remember that plugins like Neural DSP are entirely MIDI-Learnbased: you right-click a control, enable MIDI Learn, and send it a message — no CC map to memorise. A CC learned to a button toggles it; a CC learned to a knob or slider tracks it directly; a Program Change can be learned to any switchable control. If you haven't wired that up yet, the Neural DSP setup guide and the user manual walk through it. Only come back here when the basics genuinely can't reach the parameter you want.

Pitch Bend

Pitch Bend is a 14-bit message (values 0–16383), where 8192 is centre— no bend — 16383 is full up and 0 is full down. Because a key is a single press, it sends the value once. What happens when you let go is the Press mode row, which offers four behaviours: send one value and leave it there, send one value and snap back to centre on release, ride the value while the key is held, or ride it and snap back. Snap back is the "bend-and-release" that used to need a second key set to 8192 — a dive or a stab that undoes itself. Aftertouch and NRPN get the same four, returning to 0 rather than to centre. For a value you want to steer rather than trigger, a dial is still the better tool — see using a Stream Deck as an expression pedal.

Channel Aftertouch

Channel Aftertouch sends a single pressure value (0–127) for the whole channel — this is the global "how hard am I leaning on the keys" message. What it actually does is up to your gear or patch: many synths route pressure to vibrato depth, a filter, or a swell. Pick the channel, set the pressure, and the key sends it.

Poly Aftertouch is the per-note kind, one row below it in the same dropdown. It carries a Note number as well as a pressure, and on a lot of gear that note byte is not a note at all but a parameter address: an Access Virus reaches its whole Page B this way — those parameters have no CC at all — and an Allen & Heath GLD selects a mix with it. Take both numbers from the device's MIDI implementation chart. Most instruments implement channel pressure only and ignore the per-note message silently, so the panel says so on the key's Sends line.

NRPN

Some gear exposes parameters beyond the 128 standard CC numbers through NRPN — a 14-bit parameter address plus a 14-bit value (each 0–16383). MIDIRover sends it the standard way, as the four-message sequence CC 99 · 98 · 6 · 38: CC 99/98 select the parameter (MSB then LSB) and CC 6/38 set the value (MSB then LSB). You supply the parameter number and value; which parameter is which is entirely device-specific, so read it off your unit's MIDI implementation chart rather than guessing. MIDIRover sends the four messages in order and stops if one fails, so a value can never land on a different parameter from the one you addressed.

Get the number wrong, though, and the right thing happens to the wrong parameter — which on some gear is not harmless. Waldorf's Blofeld hands almost every controller number this mechanism uses to an ordinary patch parameter, so a stray NRPN edits the sound rather than being ignored, and its only defence is a single global Ctrl Receive switch. Allen & Heath document a Remote Shutdown on the Qu at NRPN parameter 95 — their own note says the mixer then needs a hard power reset. Neither is a reason to avoid NRPN; both are the reason to take the number off the chart instead of trying numbers to see what moves.

SysEx

System Exclusive is raw, manufacturer-defined data — everything from a preset dump to a proprietary parameter that has no CC at all. You paste the hex bytes exactly as your gear's MIDI implementation chart lists them. MIDIRover adds the F0 start and F7 end bytes for you if you leave them off, and accepts whatever separators the chart uses — spaces, commas, periods, colons, semicolons or dashes. If any token isn't valid hex, the field shows a red outline and nothing is sent, so a typo can never fire off a truncated, wrong message. SysEx strings are specific to each device, so always copy them from that unit's documentation — there's no universal list to fabricate from. (The field's placeholder is a harmless universal "GM System On" message you can use just to confirm the pipe works.)

Transport: Start, Continue, Stop

These three are different from everything above: they are System Real-Time messages, and each is a single byte with no channel at all — Start FA,Continue FB, Stop FC. That is why the Channel row disappears when you pick this type: there is nothing to set, and a control that does nothing would only mislead you.

They drive anything slaved to external transport — a hardware sequencer, groovebox or drum machine, or the Run and Reset gates on a MIDI-to-CV converter if you run a modular rig. The distinction worth learning is Start versus Continue, because it is audible: Start rewinds and plays from the beginning, while Continue resumes from wherever Stop left off.

Stop sends only Stop. It does not also silence notes that are still ringing — that would be extra bytes you never asked for on the wire. If something is hanging, the Panic action exists for exactly that.

Sending them: the Advanced MIDI action

Drop an Advanced MIDI action on a key, then choose the Type — Pitch Bend, Aftertouch (channel), Poly Aftertouch (per-note), NRPN, RPN, SysEx, Transport, Song Select, Song Position or Tune Request. The fields change to match: Pitch Bend and NRPN take numeric values, Aftertouch a pressure value, and SysEx a hex string. Set the channel (not needed for SysEx, which carries its own routing) and pick your MIDI Port — that choice is shared across every MIDIRover key. Press the key to send. You can name channels so a key reads, say, 10 · Drums, and the name shared across all your keys. For the full field-by-field reference, see the MIDIRover user manual.